Shopping Cart
Your cart is empty.
Mailing Lists

4 Big Bottle Wall Mounted Wine Rack

Price: From $75.00 to $85.00

Product Options



Three to six liter big bottle rack.
Holds four bottles
WS-BIG1 Wall Mount
Wine Rack Instructions

Tools Needed:
Before starting, open all Packaging for the WS-BIG1 and take inventory to make sure you have everything.
1 Neck Strip •
2 Black Plastic Couplers •
1 Spirit Level
1 Marking Pen or Pencil

1 Tape Measure
1 Screwdriver

Drill and Drill Bits (Necessary in Some Cases) •
There are four pre-drilled mounting holes in each strip, eight total, per rack. Appropriate fasteners must be utilized in every mounting hole for proper installation. Fasteners are not included with your WS-BIG1. However, we recommend the following fasteners for these surfaces:
Wood Surface: #8 x 1-1/4” wood screw
Drywall/Wallboard Surface: #8 x 1-1/4” screw with spiral inserts for the bottom two holes in each strip (4 total) and an expanding hollow wall anchor such as a toggle bolt for the top hole in each strip (2 total)
Concrete, Brick or Stucco: 3/16” x 1 ¾” masonry screw or #8 x 1 ¼” screw with appropriate size expanding anchor

NOTE: If you are attaching the WS-BIG1 to a custom Floor to Ceiling Frame (FCF) you will attach the units to the FCF using the self-drilling screws included in the FCF packaging.
WS-BIG1 Installation Instructions
1 - Determine which direction the bottle necks should point.
1 Base Strip •
8 Black Rubber Mounting Hole Caps •
1.1. If the bottle necks are to point to the right, the base strip must be installed to the left of the neck strip.
1.2. If the bottle necks are to point to the left, the base strip must be installed to the right of the neck strip.
2.1. The centerline of the first strip (either base or neck depending on bottle neck direction) should be at least 3 ½” from adjacent walls or obstructions. This allows for the bottle to overhang the rack (Fig. 1, Dim. A).
2.2. From centerline of the first strip, measure 10-14” to the centerline of the next strip. This dimension should be tailored to the specific bottle size (3L to 6L) that will be stored in the rack (Fig. 1, Dim. B).
2.3. (For multiple columns) Locate the centerline of the next strip (Fig. 1, Dim. C) twice the measurement used for Dim. A, approximately 7”, away from the prior strip. [Dim. A X 2 = Dim. C]
2.4. (For multiple columns) Continue marking the centerlines, alternating between Dim. B and Dim. C.
2 - Lay out the wall.
3.1. Reference the Fasteners section for recommended fastener types.
3.2. Using a level, ensure that each strip is plumb prior to securing it to the wall.
3.3. Note that the strips may be slightly offset vertically to achieve the proper bottle tilt. (Bottles resting on the rack should have a slight neck-down tilt).
4.1.Remove the round rubber mounting hole caps from the bag and snap them into place in the back strip.
5.1. When stacking racks, carefully remove the black plastic end caps from the top of the lower strips and from the bottom of the upper strips.
5.2. With the lower strips fastened to the wall, per the above directions, insert the provided black plastic couplers in the bottom of the upper strips and slide the strip into place such that the bottom of the coupler slides into the lower strip
5.3. Fasten the upper strip in place to the wall.
3 - Determine appropriate fasteners for the wall surface and fasten the strips to the wall.
4 - Insert the Mounting Hole Caps.
5 - Stacking racks (Optional).
Wine Master Cellars (“WMC”) warrants to the original consumer-purchaser that this product shall be free from defects in workmanship and materials under normal and reasonable use for the lifetime of the product.
WMC will, at its option, refinish or replace any product or part found to be defective during the warranty period and excludes installation charges, shipping charges, and cost of removal and reinstallation. WMC may require you to return the part(s) claimed to be defective, for its inspection - freight or postage prepaid.
This warranty does not include the cost of any inconvenience or property damage due to the failure of the product and does not cover damage due to misuse, abuse, accident, or damage arising out of transportation of this product. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER OBLIGATIONS, LIABILITIES OR WARRANTIES. In no event shall WMC be liable or responsible for INCIDENTAL OR CONSEQUENTIAL DAMAGES or for any other direct or indirect damage, loss, cost, expense or fee. Neither the WMC distributor nor the retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above. WMC’s maximum liability, in any event, shall not exceed the purchase price of the product paid by the original consumer-purchaser. Some states do not allow the exclusion or limitation of incidental or consequential damages. In such a case, the above limitations or exclusions may not be applicable.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.